Fluid solenoid valve 1 2/2 closed combined drive - adajusa.es
Fluid solenoid valve 1 2/2 closed combined drive - adajusa.es

Solenoid valve fluids 1 2/2 closed combined drive D.25

€64.31 Tax included

€53.15 tax excl.

Electrovalve for home automation, fluids or process control, threaded 1 " body in brass. Combined drive electrovalve, closed 2-way (NC), Ø of the actuator for 13mm coil. Step diameter 25 mm

Pressure max. 12.2 bar. Min pressure: 0 bar.

fluids:

  • air.
  • Inert gas.
  • Water (max. 75ºC).
  • Mineral oils.
  • Gasoleos.

Esquema neumático electroválvula 2/2 mando directo
Manufacturer: Aignep
Representative image for illustrative purposes, the article supplied will correspond to the specifications indicated.

No queries yet, leave the first!
 

1" direct drive electrovalve, 2 ways, normally closed (NC), for use with fluids or air, combined drive. Brass body and stainless steel coil control.

Step diameter 25 mm

The main hole of the valve body is opened by an imbalance between the upper and lower surfaces of the membrane, when the coil is not active there is pressure in the upper chamber of the membrane, while in the lower chamber there is only pressure in the main hole of the valve, keeping it closed. When we give tension to the coil, we set the moving core in motion, opening the piloting hole and discharging the fluid from the upper chamber directly through the center of the membrane. The pressure difference at this time causes it to open the main hole.

This type of valves are prepared to open from 0 bar.

The working pressure ranges are:

  • Minimum pressure differential between inlet and outlet (ΔP bar): 0 bar.
  • Maximum pressure differential between inlet and outlet (ΔP bar):
    • With coil size 30mm of 14W: 8.3 bar.
    • With coil size 30mm of 14VA: 5.1 bar.
    • With coil size 30mm of 21VA: 9.8 bar.
    • With coil size 36mm of 22W: 12.2 bar.
    • With coil size 36mm of 31VA: 10.6 bar.
  • Maximum permissible pressure: 12.2 bar



The electrovalve is normally closed, that is, without tension in the coil, the fluid or air will be interrupted through the electrovalve, when the coil is put into tension the passage of the fluid or air will occur.

Compatible coils for this type of electrovalve are range SOL20 (30mm) and SOL21 (36mm) for cores of diameter 13 (Coil not included)

The fluids with which this electrovalve can work are:

  • air.
  • Inert gases.
  • Water (maximum temperature 75ºC).
  • Mineral oils.
  • diesel.
  • fuel oil.

specifications:

  • Manufacturer: Aignep
  • Reference: 03F 09 1 25 N0
  • Type of control: combined drive.
  • Thread size: 1".
  • number of tracks: 2.
  • number of positions: 2.
  • Configuration: 2/2 closed (NC).
  • Operator shaft diameter (for coil): 13mm.
  • Body: Brass.
  • Guide tube, cores and spring: Inox.
  • Type of gasket: NBR.
  • Type of fluids: Press and press on air, water (max. 75ºC), mineral oils, diesel, fuel oil.
  • Maximum pressure: 12.2 bar.
  • Size ISO 228:1".
  • Ø step: 25mm.
  • Maximum fluid viscosity (cSt): 25.
  • Valve coefficient (Kv): 6.63 m³/h.
  • Minimum pressure differential (ΔP bar): 0 bar.
  • Maximum pressure differential (ΔP bar): 5.1-12.2 bar depending on the power of the coil.
  • Working temperature of the electrovalve: -10ºC to +80ºC.
  • Fluid temperature: -10ºC to +90ºC.

Dimensiones electrovalvula mando combinado
Material for professional use, install respecting the regulations in force at the place of installation.

For more information you can download the technical data sheet by clicking on the "Attachments" tab

Questions

Be the first to ask a question about this product!

Question about the product

* Required fields
(read)

16 other products in the same category:

Customers who bought this product also bought:

Reviews
Product added to wishlist
Product added to compare.